 |
| Quantity: | |
|---|---|
TPS-MTCR1200
TopsRecycling
8477800000
This machine is used to cut waste truck tyres, waste bus tyres, light truck tyres, SUV Vehicle tyres, passenger tyres etc. into rubber blocks. It is a very important and very efficient equipment in waste tyre recycling industry.
This manually waste tire strip cutter and block cutter is very popularly used in waste tyre recycling factories. Especially in China, India, Turkey etc.
Waste Tyre Strip Cutter
Waste Tire Strip Cutter
Waste Tyre Strip Cutting Machine
Waste Tyre Block Cutter
Waste Tire Block Cutter
Waste Tyre Block Cutting Machine
Very small investment on the machine;
High efficiency. It takes only one minute to cut one truck tyres (e.g size R22.5)
It takes very small area for machine installation and operation
Very convenient for the maintenance (its only maintenance is bearing lubrication and blade sharpening, when its blade gets blunt, it can be sharpened on the machine itself in situ without any disassembly, and it takes a few minutes only for the sharpening)
Running cost is very low, and the power consumption is very
The rubber blocks made on this machine is very good consistency, and with very clean edges. It is good for TDF and further shredded to rubber granules and rubber powder.
A: It is very efficient to cut any size of truck and bus tyres (both steel radial tyre and nylon tyres). It can also cut passenger tyres, but the capacity will be decreased, because the tyre size is small, it can be cut off very soon. And takes more time for tyre loading & unloading. So, we don't recommend to cut passenger tyres on this machine.
A: It depends on the tyre size and work efficiecy of the labor. If the labor works harder, the efficiency will be higher
A: In general, about 2 Kw per hour to cut about 60 pcs of tyres.
A: One operator only. However, if the tyre source is far from the machine site, it needs another person to transport the tyres to nearby the machine.
A: It can cut about 20000 pcs of tyres.
A: The blade can be sharpened by manually grinding machine in situ on the machine itself. No need to dismantle it from the machine and bring it to processing center. So, it is very convenient and cheap, the video of the blade sharpening will be provided
A: 1. Keep the blade sharp always, if it gets blunt, grinding it in situ on the machine by hand grinder
2. Lubrite the bearings regularly
3. Keep the hydraulic oil clean replace it as per the operation manual we provided.
4. Check the screw bolts and nuts regularly. Tighten them if any of them get loose.
This machine is used to cut waste truck tyres, waste bus tyres, light truck tyres, SUV Vehicle tyres, passenger tyres etc. into rubber blocks. It is a very important and very efficient equipment in waste tyre recycling industry.
This manually waste tire strip cutter and block cutter is very popularly used in waste tyre recycling factories. Especially in China, India, Turkey etc.
Waste Tyre Strip Cutter
Waste Tire Strip Cutter
Waste Tyre Strip Cutting Machine
Waste Tyre Block Cutter
Waste Tire Block Cutter
Waste Tyre Block Cutting Machine
Very small investment on the machine;
High efficiency. It takes only one minute to cut one truck tyres (e.g size R22.5)
It takes very small area for machine installation and operation
Very convenient for the maintenance (its only maintenance is bearing lubrication and blade sharpening, when its blade gets blunt, it can be sharpened on the machine itself in situ without any disassembly, and it takes a few minutes only for the sharpening)
Running cost is very low, and the power consumption is very
The rubber blocks made on this machine is very good consistency, and with very clean edges. It is good for TDF and further shredded to rubber granules and rubber powder.
A: It is very efficient to cut any size of truck and bus tyres (both steel radial tyre and nylon tyres). It can also cut passenger tyres, but the capacity will be decreased, because the tyre size is small, it can be cut off very soon. And takes more time for tyre loading & unloading. So, we don't recommend to cut passenger tyres on this machine.
A: It depends on the tyre size and work efficiecy of the labor. If the labor works harder, the efficiency will be higher
A: In general, about 2 Kw per hour to cut about 60 pcs of tyres.
A: One operator only. However, if the tyre source is far from the machine site, it needs another person to transport the tyres to nearby the machine.
A: It can cut about 20000 pcs of tyres.
A: The blade can be sharpened by manually grinding machine in situ on the machine itself. No need to dismantle it from the machine and bring it to processing center. So, it is very convenient and cheap, the video of the blade sharpening will be provided
A: 1. Keep the blade sharp always, if it gets blunt, grinding it in situ on the machine by hand grinder
2. Lubrite the bearings regularly
3. Keep the hydraulic oil clean replace it as per the operation manual we provided.
4. Check the screw bolts and nuts regularly. Tighten them if any of them get loose.
| | Provincial Econimic Development Zone, Jiangsu, China |
| | +86-15962378058 |
| |
